同时配备缝焊控制器，对焊接时间，间歇时间，焊接电流能精确的设定和控制。
Equipped with welding controller, the welder has precise control and setting functions for the welding time and intervals and welding current energy.
采用国外引进焊机确保钢带焊接时间和焊接质量。
The welding time and weld quality is guaranteed by international purchased welder.
在焊接电解电容器时，其焊接时间和焊接温度不应超过10秒钟及260摄氏度。
When soldering the electrolytic capacitor, the soldering time should never be permitted over 10 seconds, and for 260 · C of the soldering temperature.
输入预压、波头、焊接时间、保压、焊接电流等参数。
Input preloading, wave head, welding time, the pressure, welding current parameters.
在焊接时, 此间隙可忽略不计。
This gap is negligible when welding.
先焊炉底板间对接焊缝, 由中间往四同辐射对称焊接。
First, weld the butt seams on the bottom plate of the furnace, with radiating and symmetric welding conducted from the central point.
同时，通过对焊接工艺参数进行调整，研究了焊接电压电流、焊接速度、装配间隙对焊接温度场的影响。
At the same time, studied the effect of the welding temperature field by adjusted the welding process parameters of welding current, such as voltage, welding speed, assembling clearance.
通过改变超声波焊接的焊接压力、焊接时间、以及待焊件的表面状态等工艺参数来进行焊接，研究了各工艺参数对焊接接头性能的影响。
It has studied that the technological parameters ( ultrasonic welding time 、 the welding pressure 、 the surface condition of the material and so on) have effect on the properties of the welding joint.
文章讨论了钎焊时间、钎焊温度、钎焊间隙及焊后扩散处理对钎焊接头再熔化温度的影响。
This paper discusses the effect of brazing time, brazing temperature, brazing gap and diffusion treatment on the remelt temperature of the brazed joint.
然而在利用二氧化碳保护焊对汽车进行焊接时，会产生大量的焊接烟尘，危害焊接车间工人的健康。
However, carbon dioxide arc welding could produce large amounts of welding fumes which will bring great harm to the workers.
当你焊接接口时，用锡焊很管用。
Tinning the ends of the wires makes a better joint when you solder them.
恒温时间对PCD刀具焊接性能的影响
Effect of holding time on the brazing properties of PCD cutting tools
碰到焊接管材时，这些探头可手动焊接或者自动焊接。
In the case of welded tube and pipe, test heads can be provided for manual or automated weld following.
焊接时能量消耗比传统焊接方法低。
Energy for friction stir welding is lower than conventional fusion welding.
TIG自动焊的间接接触引弧
Indirect Contact striving of Automatic TIG Welding
超窄间隙焊接是采用间隙尽量小的I形坡口得到高质量焊接接头的一种高效率焊接技术。
The ultra-narrow-gap welding is a high efficient welding technology in which I groove is used.
采用该控制器可改善焊接循环，提高焊接电流和焊接时间的控制精度，工作性能稳定，程序编制灵活。
The controller can improve the cycle of welding and controlling precision of welding current and time.
双金属窄间隙焊接；
To make bi-metallic welds without buttering ( with use of NG-GTAW);
具有连续焊、点焊、间断焊功能，适合不同的焊接需要。
With continuous welding, spot welding and discontinuous welding functions, meet different welding requirements.
采用碱性药皮焊条和焊前接头预热的施焊方法，焊接的空间管道接头热应力小。
For overhead pipeline, welding with basic-compound coated electrodes and pre-welding heating of the joint will reduce the joint thermal-stress.
经加压处理的钎焊接头组织致密，接头强度随钎焊温度和钎焊保温时间的影响趋势与未加压时相一致。
The influence of different brazing temperature and holding time on strength of brazing under pressure is consistent with brazing without pressure.
焊接电流对双丝间接电弧焊电弧特性的影响
Influence of welding current on arc characteristic of twin-wire indirect arc welding
防止焊接接头脆化和晶间腐蚀是焊接技术的关键，在焊接试验基础上，制定合理的产品现场焊接工艺，包括焊接材料的选择、焊接规范参数和焊接技术措施。
These were key technique to prevent welding embrittlement and corrosion resisting in the welding joint. Spot welding practice was worked out based on the welding procedure test. Include the choice of welding material, groove patter and size design, welding variables and welding technical requirements.
多点焊拉剪搭接接头构件的最佳焊点间距研究
Study on the optimum distance between weld spots of multi spot tensile shear sheet joint
