Primary sorbite Initially these alloys were austenitic.
最初，这些合金为奥氏体合金。
Of 4 contented the same element-sorbite.
其中3个单体中均含有同一种成分一山梨醇；
The Development of Query System with Sorbite Standard
索氏体标准查询系统的开发
Martensite lath changes into fine tempered sorbite w.
材料经高温回火得到细小回火索氏体, 力学性能优良。
In the V-N complex micro-alloyed 77B and 82B steels, Sorbite clusters get more finer but the sorbite interlaminar spacing increase. 3.
钒氮复合微合金化77B、82B钢索氏体团更加细化，索氏体片层间距有所增大。
After high temperature tempering the microstructure transform into tempered Sorbite.
高温回火后组织为回火索氏体。
After heat treatment, the microstructure of the steel is tempered sorbite.
经热处理后的试样组织均为回火索氏体。
The roll barrels are mainl composed of pearlitic or temper sorbite in the microstructure.
辊身金相组织为珠光体或回火索氏体。
Study on New Heat Treatment for Ginger like Sorbite of Low Alloy Cutlery Steels
低合金刃具钢的姜块状索氏体化处理
Relationship between Cyclic Strain Behavior of Tempered Sorbite in a Rail Steel and Its Dislocation Structures
回火索氏体钢轨钢循环应变行为与位错结构关系的研究
Ex-perimental results show that contact fatigue life of mixed structure is better than that of single tem-pered sorbite.
结果表明，混合组织的接触疲劳寿命（No、Nf）高于单一回火索氏体组织。
The ginger like Sorbite forming mechanism and the high wear resistance of ginger like carbide cutter blade were studied in this paper.
本文从空间形貌上说明姜块状碳化物的形成机制，并从微观机理分析姜块状碳化物提高刀片耐磨性的原因。
Oppugning the foundation of the YB/ T 169-2000 Metallographic test method for the sorbite percent in the high carbon steel wire rod
对于YB/T169-2000高碳钢盘条索氏体含量金相检测方法评级依据的探讨
The microstructures of heat affected zones of T91/ 10CrMo910 are tempered sorbite and thin tempered lath martensite and the toughness is good.
10CrMo910热影响区和T91热影响区的组织分别为索氏体和细的回火马氏体，韧性较好。
The results indicate that, with the increase of rolling times, the grain size becomes smaller, the content of sorbite multiplicates, and the yield strength improves.
结果表明，随轧制道次的增加，晶粒尺寸逐渐减小，索氏体的含量不断增加，屈服强度逐渐提高。
Primary sorbite Of the rivers here, the Li River, Little East River, Peach Blossoms River and Banyan Lake are typical of the scenic beauty of Guilin.
水以漓江、小东江、桃花江和榕湖最有代表性。
The technology not only guarantees that there are good microstructures of the tempered troostite and sorbite in the wire rod steel, but also makes environmental pollution and human harm decrease much.
该工艺在保证盘条钢具有良好的回火屈氏体和索氏体组织外，还减少了对环境的污染和对人体的危害。
Under the condition of two-body abrasion, the abrasive wear of pearlitic steels is better than that of sorbite steel, white under the condition of three-body abrasion, the reverse is true.
在两体磨料磨损条件下，珠光体钢的耐磨性比索氏体钢好，而在三体磨料磨损条件下，则相反。
The results showed that the junction area of the hi-Cr white iron-carbon steel cast-in casting consisted of the ferrite zone and the Fe, C, Cr-containing sorbite zone.
结果表明：高铬白口铸铁-铸钢镶铸铸件结合层为铁素体带和含有Fe、C、Cr的索氏体带组织构成。
It was pointed out that obtaining fine sorbite with high toughness was the key to good fatigue resistance. Other factors such as surface quality and free ferrite in sticks were also affect fatigue properties.
指出，获得细小的高韧性索氏体组织是保证良好疲劳寿命的关键，稳定杆喷丸表面质量、游离铁素体也是影响疲劳性能的重要因素。
The main methods improving the strength of galvanized wire for bridge cable are to improve the strength of sorbite wire rod, increase drawing hardening effect and decrease strength lose in the course of galvanizing.
提高桥梁缆索镀锌钢丝强度的主要方法是提高索氏体盘条的强度、提高加工硬化效果和减少热镀锌过程的强度损失。
The test results showed that Nb could prevent recrystallization of deformed lath martensite structure at 600~ 680 ℃, and the aged structure was tempered sorbite kept lath martensite phase direction with no ferrite particles discovered.
试验结果得出在600～680℃范围内，Nb能阻止变形马氏体组织的再结晶，时效组织主要为保持板条马氏体位向的回火索氏体，未发现粒状铁素体。
Strain-fatigue properties of pearlite and tempered sorbite in a C-Mn eutectoid rail steel have been studied by fully reversed constant total strain amplitude and plastic strain behavior in strain fatigue process has been investigated.
用全反向恒应变幅试验方法，研究了C-Mn轨钢珠光体及回火索氏体的应变疲劳行为，探讨了塑性应变在应变疲劳中的作用。
In this paper, repeated quenching and tempering processing was used to not only refine the grain size and but also keep the microstructure as tempered sorbite. Good wear resistance is also desired to be obtained by the processing.
本文设计旨在既保留回火索氏体组织又能细化晶粒的多次调质热处理工艺，以期使其耐磨性得到提高。
The results showed that tempered soft zone in harden zone case produced in process of discontinuous medium frequency induction hardening which has microstructure of tempered sorbite and low hardness and low fatigue limit were major reason to cause driven gear cracking.
结果表明，因中频淬火的不连续，使淬硬层出现了回火软区，组织为回火索氏体，降低了材料的硬度和疲劳极限，最终导致从动齿轮开裂。
